HONOR BANNER COLOR

Mitee-Bite Tall Vise Jaw System

img_2322-150x150
img_2322-150x150img_2300-2tall-vise-jaw-app2pitbull-talon-versa-grip-vise-jaw-t-slot-combo-kit-with-teco-visetall-jaws-on-vise-with-pb_tg_vg-4img_2293111img_2322
Brand: Mitee-Bite CNC Fixture ClampsMitee-Bite CNC Fixture Clamps

SKU: MITEE-32266

SALE: $550.99 each

Tall Vise Jaw System

These Vise Jaws/Towers are designed to mount directly to your 4 or 6 inch vise elevating your workpiece into the 5 axis envelope. You already have the platform therefore this becomes a very simple and low cost solution. This is the only system on the market where you can loosen the vise and double the holding force!

The Towers are exceptionally versatile due to the incorporation of our TalonGrip™ and VersaGrip™ Grippers and Pitbull® clamps. Secure round or square stock easily by using a vise or by mounting towers directly to your t-slot or grid table. Low profile gripping saves material cost and no workpiece preparation saves machine and labor cost.

VISE APPLICATION:

  • Mount jaws to either 4 or 6 inch vise with MITEEBITE.COM facing
    outboard keeping mounting bolts loose.
  • Determine which grippers will be used, install and tighten grippers
    hand tight. If VersaGrips™ are being used to grip round stock, place in outboard bores. Do not tighten screws at this point. Tighten vise lightly onto workpiece allowing jaws to center themselves, adjust VersaGrips™ and tighten gripper screws and mounting bolts for both jaws.
  • Loosen vise jaw for load/unload clearance of workpiece. Install support/drive/pivot bolt.
  • Setup is complete. Tighten drive bolt allowing grippers to penetrate .010-.060″ on material < 40Rc.
  • For additional holding force, loosen vise handle which will eliminate any jaw lift that may have occurred and depending on amount of torque can increase pressure to over 9,000 lbs.

T-SLOT & GRID TABLE APPLICATION:

  • Using vertical counter bores on outboard edges of jaws, install mounting bolts into t-nuts or grid plate and adjust accordingly. Do not tighten at this time.
  • Select appropriate length support/drive/pivot bolts, thread lower bolt into jaw prior to sliding opposite jaw into place. Insert upper bolt and adjust as necessary for work-piece.
  • Place workpiece between jaws and lightly tighten upper bolt & loosen lower bolt until all grippers contact workpiece.
  • Loosen upper support bolt until adequate workpiece clearance for part removal is obtained.
  • Tighten vertical mounting bolts.
  • Upper support bolt is now the “drive bolt” for securing and releasing workpiece.
  • To increase holding force loosen lower bolt creating pivot point on upper bolt for aggressive machining.
  • Any size t-nuts can be utilized. We provide 16mm t-nuts (most popular size) which also fits 5/8 t-slots.

GRIPPER CONFIGURATIONS:

  • Round stock: use 4 VersaGrips™, two in each outboard bore. Adjust so all “points” make contact simultaneously. If small diameter workpiece, two parts may be held at one time.
  • Maximum of 8 TalonGrips™ can be used, 4 in each jaw for maximum line contact.
  • If down force is necessary or additional holding force use 2 Pitbull® clamps. One in the center of each jaw and one TalonGrip™on each side of Pitbull® clamps. Tighten jaws into grippers then tighten each Pitbull® clamp.

KIT CONTENTS:

  • 2 Jaws
  • 4 Talongrip™ 3/4″ grippers with M5 screws
  • 4 Versagrip™ grippers with M5 screws
  • 1 Talongrip™ 3/4″stop with M5 screws
  • 2 Pitbull® blunt edge clamps with M6 screws
  • 2 M12 x 200mm support bolts
  • 2 M12 x 100mm support bolts
  • 2 M12 x 65mm support bolts
  • 4 M12 x 55mm mounting bolts
  • 4 M12 x 16mm T-nuts
Tall Jaws
 
 
Part NumberJaw Set DescriptionVise SizeMtg. BoltsABCDEFGH
32266 6″
150mm
4 or 6″ 100mm/150mm M12x55mm SHCS 6.00 150mm 6.00 150mm 1.06 26.92mm 3.88 98.55mm 2.50 63.50mm 0.69 17.53mm 0.94 23.88mm 4.96 125.98mm

Latest products

Lockhart Tactical 12GA STATAS - Sentry Tactical Automatic Trip Alarm System
2020-05-13 19:54
LIMITED TIME ON SALE!NOW SHIPPING SAME DAY - WORLDWIDE!     AVAILABLE ADAPTERS:1) 209 12GA Shotgun Primers (adapter sold separately)2) Const
LT-STATAS SALE: $0.00 each
Lockhart Tactical STATAS Bang Master Kit
2020-06-10 18:21
NOW SHIPPING SAME DAY - WORLDWIDE! The STATAS Bang Master Kit is perfect for those who want a full setup ready to go out of the box. The Included
LT-STATAS-BANG-MASTER-KIT SALE: $250.00 If Qty 4+
Tru Flare 15mm Bear Bangers (6 Pack)
2020-05-31 16:32
The bearbangers travel approx. 125+ feet then explode with a very loud bang at the end of flight. the bearbangers are orange 
TRUFLARE-4007-144 SALE: $29.95 each
Lockhart Tactical STATAS Double Deployment Pouch
2020-06-08 21:57
  The Lockhart Tactical Double Deployment Pouch allows you to Store, Carry and Deploy two (2) STATAS kits. Attach the pouch to your molle
LT-STATAS-DD-POUCH SALE: $35.55 each
Lockhart Tactical STATAS Hybrid Adapter (.209 12GA Primer) GEN 1
2020-06-08 21:20
The Lockhart Tactical STATAS Hybrid Adapter expands the capabilites of the STATAS for use .209 12GA Shotgun Primers.Fit hundreds of primers in the sam
LT-STATAS-HYBRID-ADAPTER SALE: $31.10 If Qty 4+
Tru Flare 12GA Bear Bangers (5 Pack)
2020-05-31 16:32
No Firearms Lisense Required as this is not considered ammunition and instead a safety device! The bearbangers travel approx. 125-150+ feet then
TRUFLARE-12GA-BEAR SALE: $29.95 each
Results 1 - 6 of 13